Drills and Drill Bits
Grainger Cor Rad End Mill 1/2 Carb 0.0100 rad
The Micro 100 Corner Radius End Mill is a bright finish end mill made of solid carbide with a corner radius of 0.031". It has 2 flutes and a right hand spiral. The overall length is 2.5" and shank diameter is 0.25". It is designed for high feed milling of aluminum, brass, bronze, copper, plastic and other non-ferrous metals. This end mill provides a strong, precision cutting edge and smooth milling action. Its bright finish resists corrosion and reduces heat buildup.
Grainger Cor Rad End Mill 1/8 Carb 0.0100 rad
The Micro 100 Corner Radius End Mill is a carbide end mill with a corner radius of 0.031 inches. It has a 1/4 inch shank diameter and a 1/2 inch cutting diameter. The overall length is 2 inches. It has 2 flutes and can be run at speeds up to 12,000 RPM with feed rates up to 80 IPM. This end mill is made of solid carbide and can machine steels, stainless steels, cast iron, aluminum, and other non-ferrous materials. It features a TiAlN coating for increased tool life and heat resistance. The corner radius design allows for strong cutting edges and smooth wall blends.
Grainger End Mill Kyocera MEC 0500S50011 0.5000
The Kyocera 61NV71 is a 4 flute end mill made of micrograin carbide with a TiAIN coating. It has a 1/2" shank diameter, 1-1/2" overall length, and 3/4" cutting diameter. The end mill features variable helix flutes for reduced harmonics and chatter and high positive radial and axial rake angles for easy chip evacuation. Recommended cutting parameters are 12,000-18,000 RPM with feed rates from 0.004-0.012 IPR depending on material. It is well-suited for slotting, profiling, and facing in steels, stainless steels, cast iron, aluminum, and other non-ferrous metals.
Grainger End Mill Kyocera MEC 32S2511T 32mm
The Kyocera 170HM0 is a 1/2" diameter, 4 flute, high speed steel end mill with a 1-1/2" overall length. It has a TiAlN coating for increased hardness and heat resistance. The end mill has a 30 degree helix angle and is center cutting for plunge cuts. It is designed for slotting, profiling, and contouring in steels, cast iron, aluminum, and other non-ferrous metals at speeds up to 325 SFM. The end mill has a tolerance of +/- .0005" and comes with a 30 day warranty from the manufacturer.
Grainger Sq. End Mill Single End Carb 0.0210
The Grainger Approved Square End Mill Single End is a high-speed steel end mill with a square end for milling slots, keyways, and pockets. It has four flutes and a right-hand spiral. The overall length is 3 inches and the shank diameter is 1/2 inch. This end mill is uncoated and made in the USA. It can be used for slotting, side milling and pocketing in low carbon steels at surface speeds up to 120 SFM when paired with rigid setups.
Grainger Thread Mill Carbide
The Micro 100 16R736 is a 1/4" diameter, 3/4" long, 4 flute carbide thread mill with a right hand spiral flute. It has a TiAlN coating and can cut 60-62 HRC materials. The thread mill has a 1/4"-28 UNF shank and can cut thread sizes from #10-24 through 1/4"-28. It has a neck relief below the thread for improved chip flow. The thread mill is made in the USA and has AlTiN nano coating for heat and wear resistance when cutting steel alloys.
Grainger Thread Mill Carbide
The Micro 100 16R733 is a 1/4" diameter, 3/4" long, 4 flute, right hand thread mill made of solid carbide. It has a TiAlN coating and can cut a variety of materials including steel, stainless steel, cast iron, aluminum, copper, brass, bronze, plastics and composites. It has a 1/4" shank and is designed for high speed machining with speeds up to 21,000 RPM. The thread mill can produce right hand threads from 24 to 80 threads per inch in a variety of thread forms including UN, ACME and worm threads. It is manufactured in the USA by Micro 100 Tool Corporation.